Reviews
You might also need
Brewly BWH30L 30L Brewery & Water Heater
The Brewly BWH30L is an efficient, compact 2500W semi-automatic brewer with adjustable malt basket for efficient sparging, bazooka bottom filter and tap. You mash, blanch and boil in the same vessel - Cooling coil sold separately. Via the clear digital display, you can easily set the temperature and time. Can also be used as a sparge water kettle.The malt is placed in a malt basket with a perforated insert that can be easily lifted up with the steel handle in two steps for easy leaching after mashing.Internally, there is a volume level gauge set on the stainless steel wall.Brewly BWH30L Brewery- Material: Polished stainless steel (AISI 304)- Brewing volume: 30 liters (max), at least 15L batches are recommended.- Total volume: 35 litres- Digital Controller with clear display - Set temperature and time.- Temperature range 25°C to 100°C, adjustable in steps of 0.1°C.- Temperature control up to 100°C, with +-1°C accuracy.- Power: 2500W in total (adjustable in 700W and 1800W, or both elements at the same time which gives 2500W). 10-16A fuse is recommended. The heating elements are placed under the base to avoid caramelization of the wort and to reduce burning.- Malt basket with steel handle: Can be raised in several steps.- Maximum recommended malt quantity is 8 kg.- Tap with Bazooka mesh-screen filter (raised Mesh-screen bottom filter for efficient separation of hops from the wort)- Strong glass lid- Height: 67 cm- Diameter: 36 cm (without handle and faucet)- Weight: 10 kg (freight carrying weight 40 kg)- Instruction manual- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).
Brewly BWH30L Brewery & Water Heater Kit 1
Brewery 30L with 8,8m chiller. The Brewly BWH30L is an efficient, compact 2500W semi-automatic brewer with adjustable malt basket for efficient sparging, bazooka bottom filter and tap. You mash, blanch and boil in the same vessel - Cooling coil chiller 8,8m included. Via the clear digital display, you can easily set the temperature and time. Can also be used as a sparge water kettle.The malt is placed in a malt basket with a perforated insert that can be easily lifted up with the steel handle in two steps for easy leaching after mashing.Internally, there is a volume level gauge set on the stainless steel wall.Brewly BWH30L Brewery- Material: Polished stainless steel (AISI 304)- Brewing volume: 30 liters (max), at least 20L batches are recommended.- Total volume: 35 litres- Digital Controller with clear display - Set temperature and time.- Temperature range 25°C to 100°C, adjustable in steps of 0.1°C.- Temperature control up to 100°C, with +-1°C accuracy.- Power: 2500W in total (adjustable in 700W and 1800W, or both elements at the same time which gives 2500W). 10-16A fuse is recommended. The heating elements are placed under the base to avoid caramelization of the wort and to reduce burning.- Malt basket with steel handle: Can be raised in several steps.- Maximum recommended malt quantity is 8 kg.- Tap with Bazooka mesh-screen filter (raised Mesh-screen bottom filter for efficient separation of hops from the wort)- Strong glass lid- Height: 67 cm- Diameter: 36 cm (without handle and faucet)- Weight: 10 kg (freight carrying weight 40 kg)- Instruction manual- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).
Recently visited products
Tilt PRO Hydrometer and Thermometer - Black
Designed for high performance production scale stainless steel fermentation tanks, our new Tilt® Pro brings Tilt technology to professional craft brewers. At 3x the volume and weight of our original Tilt hydrometer, the Tilt Pro's larger size allows us to more than double the battery life with preinstalled Energizer® AA lithium batteries that will keep it powered for 3 to 5 years depending on use. So much time you may forget your Tilt actually runs on a battery!The extra size and weight comes with an extra bonus: improved specific gravity stability at high krausen so you will see a steadier read-out on your iPhone, Android, or Raspberry Pi. In addition, we have boosted range with a high-gain antenna that in testing increased range by 20% vs. our original Tilt. Now you can see your Tilt through thicker heads of foam and heavier stainless steel walls. To top it off we've included the extra decimal of precision available from the sensors and to the read-out so there are now decimal degrees Fahrenheit as well as higher resolution Celsius. Specific gravity now reads out to the 10,000th place (for example 1.0000). You can now see fermentation activity dropping less than a brewer's point per day. In all we've made several adjustments we believe the craft beer professional (and serious home brewer) is sure to appreciate.Specifications TILT PRO WIRELESS HYDROMETER AND THERMOMETERSize: 1.7" (43mm) diameter (max) by 5.4" (140mm) tallWeight: 5.4 ounces (153g)Specific Gravity Measurement Range: 0.9900 - 1.1200Specific Gravity resolution: 0.00001Temperature Measurement Range: 0°F - 140°F (-17.8°C - 60°C)Note: Installed lithium batteries include a built in PTC (heat activated fuse) that will temporarily cut power if batteries exceed 140°F.Temperature resolution: 0.1°F (0.1°C)Absolute Maximum Temperature Range: -40°F to 185°F (-40°C to 85°C)Battery: User-replaceable, 2x 1.5v AA battery (Li/FeS2), widely sold as "Energizer® AA Ultimate Lithium".If using multiple Tilt hydrometers for different batches of fermenting beer you must use a different color for each batch. The app will not read multiple hydrometers of the same color.Each Tilt comes calibrated and ready to go with a pre-installed battery. Just download the free app, sanitize your Tilt, drop in your fermenter, and start taking readings with your phone, tablet, or Tilt Pi. Download the free Tilt app at the Apple App Store or Google Play Store or get the free Tilt Pi download.
Weyermann Munich-2 Malt 1kg Crushed
Medium coloured malt with characteristic malty aroma. Rich flavours of bread and honey with notes of biscuit.Good for adding complexity and colour to most beer styles, and traditionally used at 100 % of the grain bill for traditional German dark lager styles.Munich I is the darker version of the Munich malts from Weyermann®. Slightly lower levels of enzymatic power than in paler base malts.Weyermann Munich-2 Malt 1kg CrushedGrain type: barleyColour: 20 - 25 °EBC (8 - 10 Lovibond)Content: 1kg crushed barley malt Grain type: barley
Milwaukee Electrode Rinse Solution 20ml
Electrode rinse solution (deionised water) is ideal for using as an intermediate rinse between samples or calibration solutions to avoid cross contamination. This rinse solution is also ideal for removing basic salt deposit buildup on the probe or cap caused by storage solution evaporation. Even though salt deposit buildup is normal, it should be removed before measurement or calibration.Electrode rinse solution should not be a substitute for cleaning or storage solutions. Sachet packaging means that you get fresh solution every time. Ideal for infrequent or field use. No risk of using an expired calibration solution. Milwaukee solutions are designed to help you achieve reliable and repeatable measurements while extending the life of your electrode.DESIGN FEATURESElectrode Rinse SolutionFundamental for gently rinsing the electrode between like samples or calibration solutions as well as rinsing off salt deposit buildup.Sealed against light and airIdeal for on-the-spot calibrationSimply open, insert the tester or electrode into the sachet and gently stir
Tilt Hydrometer and Thermometer - Green
Designed for home brewing, the Tilt hydrometer lets you instantly read your brew's specific gravity and temperature on your compatible Apple iPhone/iPad or Android smartphone/tablet or Tilt Pi. Most Bluetooth 4.0+ devices will work with the Tilt. You can then optionally log data to the cloud using our free Google Sheets template or other 3rd party cloud platforms. See our Apps section for more detail.The specific gravity is accurate +/- 0.002 within the Tilt's range of 0.990 to 1.120. The thermometer is accurate +/- 1 degree F (+/- 0.5 degree C).Our goal is to help home brewers brew better beer. The Tilt hydrometer allows you to check the specific gravity and temperature of your beer while it's fermenting, without ever having to open your fermenter or pour out any of your precious brew. This makes brewing more consistent and easy to track. Here are some of the new features of the Tilt:Range: Better reception and range. With the increased transmission power your Tilt will send data through larger, thicker-walled fermenters.Precision: Upgraded sensors. With an improved temperature sensor and accelerometer your Tilt will operate with more precision. Efficiency: We've reduced power consumption so more brews, less battery.New Look: Newly designed custom circuit board and harness.If using multiple Tilt hydrometers for different batches of fermenting beer you must use a different color for each batch. The app will not read multiple hydrometers of the same color.Each Tilt comes calibrated and ready to go with a pre-installed battery that lasts 12-24 months depending on usage. Just download the free app, sanitize your Tilt, drop in your fermenter, and start taking readings with your phone, tablet, or Tilt Pi. Download the free Tilt app at the Apple App Store or Google Play Store or get the free Tilt Pi download.
Plastic container with lid 215ml
Plastic container with lid 215ml. Made in Polypropylene plastic with snap cap of polyethylene (LDPE). Plastic container with lid 215mlHeight: 3 cmDiameter: 10 cm.Quantity: 1pc
Tilt Hydrometer and Thermometer - Red
Designed for home brewing, the Tilt hydrometer lets you instantly read your brew's specific gravity and temperature on your compatible Apple iPhone/iPad or Android smartphone/tablet or Tilt Pi. Most Bluetooth 4.0+ devices will work with the Tilt. You can then optionally log data to the cloud using our free Google Sheets template or other 3rd party cloud platforms. See our Apps section for more detail.The specific gravity is accurate +/- 0.002 within the Tilt's range of 0.990 to 1.120. The thermometer is accurate +/- 1 degree F (+/- 0.5 degree C).Our goal is to help home brewers brew better beer. The Tilt hydrometer allows you to check the specific gravity and temperature of your beer while it's fermenting, without ever having to open your fermenter or pour out any of your precious brew. This makes brewing more consistent and easy to track. Here are some of the new features of the Tilt:Range: Better reception and range. With the increased transmission power your Tilt will send data through larger, thicker-walled fermenters.Precision: Upgraded sensors. With an improved temperature sensor and accelerometer your Tilt will operate with more precision. Efficiency: We've reduced power consumption so more brews, less battery.New Look: Newly designed custom circuit board and harness.If using multiple Tilt hydrometers for different batches of fermenting beer you must use a different color for each batch. The app will not read multiple hydrometers of the same color.Each Tilt comes calibrated and ready to go with a pre-installed battery that lasts 12-24 months depending on usage. Just download the free app, sanitize your Tilt, drop in your fermenter, and start taking readings with your phone, tablet, or Tilt Pi. Download the free Tilt app at the Apple App Store or Google Play Store or get the free Tilt Pi download.
PVC Hose 12mm/15mm (1/2") - per meter
Suitable as acid and laboratory hose and as vacuum hose. Resistant to acids, saline, alkali, flavor, soap and synthetic detergents, sulfates, animal and vegetable oils, ethyl alcohol and glycol.Not resistant to organic solvents, esters, ketones, acetone, tri and aroma, hydrocarbons.PVC HoseInner diameter: 12mmOuter diameter: 15mmSize: 1/2"Working temperature: -10°C to + 50°C, but should not be used at normal working pressure at temperatures higher than + 30°CColor: TransparentMaterial: Made of soft transparent PVC.Approved for use in the food industry.NOTE: Sold per meter, so if you select 2 in the selection box for number, you get 2 meters of hose. The dimensions can differ by about +/- 10mm.
Milwaukee Cleaning Solution 230ml
Cleaning solution is ideal for cleaning all pH, ORP and TDS meter's probes. To help maintain high performance and accuracy for any electrode, regular cleaning is required to remove the build up of dirt and setiment on the glass or carbon surfaces of a sensing probe. Use M10016B to help extend the life of the meter's electrode. Electrode cleaning solution should not be a substitute for rinse and or storage solutions. Sachet packaging means that you get fresh solution every time. Ideal for infrequent or field use. No risk of using an expired calibration solution. Milwaukee cleaning solutions are designed to help you achieve reliable and repeatable measurements while extending the life of your electrode.DESIGN FEATURESFundamental for gently cleaning the electrode between uses and before storage.Sealed against light and air.Ideal for on-the-spot cleaning too.Simply open, insert the tester or electrode into the sachet and gently stir let soak for 15 minutes.