Temperature & Fermentation Control

Brewbelt by Better Brew EUROPEAN VERSION - EU Plug. Homebrew Heat Belt - 25W – Round 2-Pin EU Plug. Keep your yeasties snug and warm with this simple to use heat belt. This is a heating belt that goes round your bucket, keg demijohn or other fermenter to keep it warm so your yeast ferments at it's preferred temperature. Perfect if you need to keep your brew in a spare room, garage of cellar where the temperature is less than idea for brewing. Simple to adjust the temperature by changing the position of the belt. Instructions included.- Gives you a quicker, more complete fermentation. - Easy to store away after use unlike heat pads.Can be used on:- Barrels - Kegs - Carboys - Buckets - or 2 Demijohns side by side

Heat Pad by Better Brew EUROPEAN VERSION - EU Plug. Homebrew Heat Pad - 25W – Round 2-Pin EU Plug. Keep your yeasties snug and warm with this simple to use Heat Pad. Perfect for your bucket, keg, demijohn or other fermenter to keep it warm so your yeast ferments at it's preferred temperature. Perfect if you need to keep your brew in a spare room, garage of cellar where the temperature is less than idea for brewing. Instructions included.- Gives you a quicker, more complete fermentation. - Easy to store away after use unlike heat pads.Can be used on:- Barrels - Kegs - Carboys - Buckets - DemijohnsDiameter: ca 30 cmThickness: ca 5 mm

The Brew Cooler is a waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters up to 30L. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler worksThe function is simple, place your fermenter inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler 30L specificationsHeight: 60 cmLength 40 cmWidth: 40 cmMaterial: Tough black polyester Kraftig svart polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.

The Brew Cooler XL is an extra large waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters and kegs up to 30L. Either one 30L fermenter or two cornelius kegs fits inside. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler XL worksThe function is simple, place your fermenter or keg(s) inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler XL 30L specificationsHeight: 70 cmLength 40 cmWidth: 40 cmInternal supports: 60cm Vertical rib supports keeps the bag upright by itself.Material: Tough black polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.Note: Fermenters, kegs or other accessories are not included.

Brewly AC-211 Digital Universal Thermostat. EU-version power cord (UK power cord not included). Can control one Heating source and one Cooling source. Sensor included.

Brewly TC-320 Digital Universal Thermostat. EU-version power cord (UK power cord not included).

Coobra Universal thermostat with EU-connections for cooling & heating at the same time and control both manually and via Wifi app.Perfect for home brewing, fermentation breeding, incubation, greenhouse, etc.- Intelligent digital display temperature controlled outlets- Temperature range -30 - 105 ℃- Supports both Celcius and Fahrenheit- WiFi 2.4GHz wireless connection- Mobile Smartlife APP control- Manual control or app controlled.- Double relay output: connect cooling & heating at the same time- automatic alarm for high/low temperature- temperature peak, Update once in 1s- Heating/cooling mode- temperature unit conversion- Programmable in up to 7 day intervals- compressor delay protection.- Temperature sensor with 150cm cord and suction cup for fastening.

The Grainfather Digital Temperature Controller replaces the temperature display. With this you can control the heating and the cooling (if you have the Grainfather Glycol Chiller) of your fermenter by dialing in a temperature or even setting a temperature schedule (can set up to 5 stages). This snaps on easily via magnets and pogo pins with no extra cords or clutter.Control the heating element and Glycol Chiller (available separately)Choose between imperial and metric (C° & F°)Total of 4 fermentation profiles with up to 5 steps each (2 are pre-set for a lager and an ale, 2 are custom)Hysteresis is customisable and able to be set at 0.1 intervals between a range of 0.1°C – 1.9°C & 0.2°F - 2.9°F (the default setting is 0.5°C)

Inkbird WiFi ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - WIFI smart controller supports both IOS & Android，WIFI supports 2.4GHz Wi-Fi router, free APP “InkbirdSmart” which is able to monitor temperature at any time.- Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

Inkbird ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

INKBIRD ITC-310T-B is a dual relay thermostat which can be set to automatically control 12 individual temperatures for 12 time slots. It is widely used for homebrew, aquarium, pet breeding, hatching, fermentation, seed sprouting and etc.12 individual temperatures for 12 time slots: INKBIRD ITC-310T-B can be set 12 individual temperatures for 12 time slots. Once the practical temperature reaches its set temperature, its timer will be started automatically, which will be much better and more precise for the monitored creatures and/or plants.Wide application contexts: INKBIRD ITC-310T-B is widely used for homebrew, aquarium, pet breeding, hatching, barbecue, boiler temperature control, geothermal temperature control, heating pump constant temperature cycle, strain culture fermentation, seed sprouting, electric heating, electric oven, over-temperature protection and automatic temperature control system of all kinds of electrical equipment and etc.Flexible control mode: it supports single mode and cycle control mode; we can choose and/or switch the control mode based on our practical needs.Specifications INKBIRD ITC-310T-BTemperature Control Range: -50~120°C/-58~248°FTemperature Resolution: 0.1°C / 0.1°FMeasuring Accuracy: ±1°C (-50 ~ 70°C) / ±1°F(-58 ~ 158°F)Temperature Control Mode: On/Off Control, Heating and CoolingTiming Accuracy: 24 hours±1.7sTiming Range: 1~999 (min/hour/day)Periods of Time Max: 12 periodsCycle Setting: 1-999 times cycle, or 00 infinite cycleInput Voltage: 100 ~240VAC, 50Hz/60HzControl Output Current: Max.10AVoltage: 100~240V ACPower: Max.1200W(120V)/2200W(220V)Alarm: High and Low Temperature AlarmSensor Type: NTC Sensor(including)Sensor Length: 2m / 6.56ftRelay Output: Cooling(10A,100-240VAC)Heating(10A,100-240VAC)

The heat pad ensures constant brewing temperature which is crucial for the success of brewing beer, wine or spirits. To be placed under the fermenter. Suitable for fermentation in cold areas such as in a refrigerator or in the basement, garages or on the balcony. Provides a low constant heat to the fermenter which aids yeast activity and helps avoid stuck fermentations.Use preferrably in cojunction with an Universal Thermostat (not included).Features:- Inexpensive to run. - Voltage: 220-240V EU-version power cord (UK power cord NOT included).- Power: 25W- Width: 32 cm- Length: 32 cm

This RAPT wifi connected temperature controller box will enable you to monitor, track and control heating and cooling devices remotely through the internet via the Android or Iphone APP. Set complex temperature profiles so the temperature will automatically change over time. Universal thermostat. NOTE! EU-power plugs 220-240V (not as picture shows).The Google Play Android App can be downloaded via the link below.https://play.google.com/store/apps/details?id=io.raptOr search for "kegland rapt" The Apple App Store RAPT App can be downloaded via the link below.https://apps.apple.com/th/app/ rapt/id1573192994Or search for "kegland rapt""This app is a web mobile wrapper that allows you to browse the RAPT portal/website so that the website renders into a mobile device screen increasing usability on your device.  It also gives you the added functionality of push notifications to your mobile device." This temperature connects with the RAPT web portal meaning that you can monitor, log and control the devices plugged into this temperature controller box remotely.The colour screen clearly displays temperature, graph of future and past temperature settings and makes it much easier to perform profile temperature steps.This plug and play temperature controller box has two clearly marked blue and red power sockets for heating and cooling so you can control a fridge or heating device at the same time to completely monitor and control the temperature. Each power outlet is rated to 10amp (2400 Watt max).PID IncludedThis temp controller box comes with PID heating function often used for higher powered devices. This greatly reduces the chance of scorching and will deliver better temperature control with less fluctuation.Temperature RangeThe temperature range of this device will enable you to control devices from -20C and up to 120C.Various Mounting OptionsThis innovative design enables you to panel mount this controller, mount to a hanging point or hook, mount on top of a fridge or brewery. Simply unscrew the mounting plate and switch the mounting to your preferred orientation.RAPT Wifi CompatibleThis product will connect with the https://app.rapt.io/ portal.  This portal will enable you to monitor, control and log past temperature and also show a future projection of temperature profiles that you might have running.